Finminer

ATrump · November 30, 2018, 4:15pm

What about cryptonight?

nanominer · December 3, 2018, 10:01am

Everything is fine with CryptoNight, we support in on AMD and Nvidia

ATrump · December 3, 2018, 12:43pm

And CPU too? Can it be mined with FinMiner on CPU only?

nanominer · December 3, 2018, 2:28pm

No, you can use CryptoNight (or Ethash) on GPUs and RandomHash on CPU
By the way, you have wrong ports indicated for PASC on nanopool in your pool list.

ATrump · December 3, 2018, 7:37pm

Thanks. I’ll check it.
By the way you can contribute to our git too. Pool templates are here, and integrations of FinMiner are here.

salvo2002 · December 8, 2018, 7:04pm

Thought I would give FinMiner a try… noticed an increase in stale shares immediately. Opened a ticket on github – https://github.com/FinMiner/FinMiner/issues/28

I switched from Claymore to PhoenixMiner when they came out with a Linux version. PhoenixMiner had the same issue (stale shares) because the miner didn’t recognize/was not tuned for the OpenCL driver version installed…

@nanominer, if you get this fixed, I intend on doing a side-by-side comparison with PhoenixMiner like I did with Claymore…

nanominer · December 10, 2018, 6:18am

Hi, @salvo2002 thanks for this results.
I appreciate it very much.
We will check it and try to figure out the reason.

oakmaster · December 12, 2018, 2:58am

What pool are supported by finminer I tried using MPH and it didn’t seem to connect also does finminer support pools with login name instead of eth add

salvo2002 · December 14, 2018, 1:06am

@ATrump

v2.4.6 is out…

https://github.com/FinMiner/FinMiner/releases/download/v2.4.6/FinMiner-linux-2.4.6.tar.gz

Less stale shares on AMD Ethash

ATrump · December 16, 2018, 6:11am

Updated in HiveOS 0.6-06@181215.

salvo2002 · December 21, 2018, 5:08am

PhoenixMiner 4.0b vs. FinMiner 2.4.6

Just over 24hrs of testing… PhoenixMiner on top with a margin of 206 more accepted shares.

Both running on Hiveon ETH pool
Each miner configured with 3 x RX570s 8Gb & 2 x RX580s 8Gb
Each miner set to autotune
HiveOS autofan control

-------------------/run/hive/miners/phoenixminer/config.txt-------------------
-mport 3335
-rmode 1
-logfile /var/log/miner/phoenixminer/phoenixminer.log
### USER CONFIG ###
-coin ETH
-gpus 12345

-------------------/run/hive/miners/finminer/config.ini-------------------
wallet = 0x
algorithm = ethash
rigPassword = x
pool1 = naw-eth.hiveon.net:4444
pool2 = naw-eth.hiveon.net:14444
pool3 = eu-eth.hiveon.net:4444
pool4 = eu-eth.hiveon.net:14444
mport = -3338
logPath = /var/log/miner/finminer/finminer.log
coin = ETH
rigName = cyrilRX10.finminer
devices = 5,6,7,8,9

Toxa · December 19, 2018, 9:19am

У меня почему-то нет статистики (см. вложение).

Это можно исправить? или необходимо внести дополнительные настройки?

ATrump · December 19, 2018, 4:15pm

Настройки нормальные, finminer пока не умеет передавать статистику Паскаля через API, ждём пока пофиксят.

Toxa · December 19, 2018, 4:24pm

жаль!

ATrump · December 25, 2018, 7:57pm

Заморочился с парсингом лога. Вывел статистику от туда.

Toxa · December 26, 2018, 6:43am

благодарю, так значительно удобнее!

nanominer · December 28, 2018, 11:20am

Toxa · December 28, 2018, 11:42am

Планируется ли добавления майнера:

В следующую сборку Hive?

ATrump · December 29, 2018, 5:40am

Работаем над этим, но по срокам пока не понятно.
Если хочется напоследок вскопнуть эфир на 1063 можно обратить внимание на claymore 12.0 - он так же экономно расходует память, как и nanominer:

Toxa · December 29, 2018, 6:31am

Так и делаю, но Claymore отказывается работать в паре с Finminer по причине нехватки памяти, а этот майнер решил бы эту проблему.