Hi,
during first setuo i managed to run the 6800 XT with Hive OS (06-203) with phoenix miner and the card produced around 60 MH/s.
Since I tried adding WLAN to the rig, and afterwards complety installed a new image via hive-replace now the 6800 XT always produces 0 MH/s
the dmesg output shows some failures:
[ 456.789480] amdgpu 0000:04:00.0: amdgpu: in page starting at address 0x00000085fffff000 from client 27
[ 456.789486] amdgpu 0000:04:00.0: amdgpu: GCVM_L2_PROTECTION_FAULT_STATUS:0x00301030
[ 456.789491] amdgpu 0000:04:00.0: amdgpu: Faulty UTCL2 client ID: TCP (0x8)
[ 456.789496] amdgpu 0000:04:00.0: amdgpu: MORE_FAULTS: 0x0
[ 456.789500] amdgpu 0000:04:00.0: amdgpu: WALKER_ERROR: 0x0
[ 456.789504] amdgpu 0000:04:00.0: amdgpu: PERMISSION_FAULTS: 0x3
[ 456.789508] amdgpu 0000:04:00.0: amdgpu: MAPPING_ERROR: 0x0
[ 456.789512] amdgpu 0000:04:00.0: amdgpu: RW: 0x0
[ 456.815302] amdgpu 0000:04:00.0: amdgpu: [gfxhub] page fault (src_id:0 ring:24 vmid:3 pasid:32771, for process PhoenixMiner pid 23998 thread PhoenixMiner pid 24031)
[ 456.815315] amdgpu 0000:04:00.0: amdgpu: in page starting at address 0x00000085fffff000 from client 27
[ 456.815321] amdgpu 0000:04:00.0: amdgpu: GCVM_L2_PROTECTION_FAULT_STATUS:0x00301030
[ 456.815327] amdgpu 0000:04:00.0: amdgpu: Faulty UTCL2 client ID: TCP (0x8)
[ 456.815331] amdgpu 0000:04:00.0: amdgpu: MORE_FAULTS: 0x0
[ 456.815336] amdgpu 0000:04:00.0: amdgpu: WALKER_ERROR: 0x0
[ 456.815340] amdgpu 0000:04:00.0: amdgpu: PERMISSION_FAULTS: 0x3
[ 456.815344] amdgpu 0000:04:00.0: amdgpu: MAPPING_ERROR: 0x0
[ 456.815347] amdgpu 0000:04:00.0: amdgpu: RW: 0x0
[ 456.824320] amdgpu 0000:04:00.0: amdgpu: [gfxhub] page fault (src_id:0 ring:24 vmid:3 pasid:32771, for process PhoenixMiner pid 23998 thread PhoenixMiner pid 24031)
[ 456.824337] amdgpu 0000:04:00.0: amdgpu: in page starting at address 0x00000085fffff000 from client 27
[ 456.824345] amdgpu 0000:04:00.0: amdgpu: GCVM_L2_PROTECTION_FAULT_STATUS:0x00301030
[ 456.824352] amdgpu 0000:04:00.0: amdgpu: Faulty UTCL2 client ID: TCP (0x8)
[ 456.824358] amdgpu 0000:04:00.0: amdgpu: MORE_FAULTS: 0x0
[ 456.824363] amdgpu 0000:04:00.0: amdgpu: WALKER_ERROR: 0x0
[ 456.824369] amdgpu 0000:04:00.0: amdgpu: PERMISSION_FAULTS: 0x3
[ 456.824373] amdgpu 0000:04:00.0: amdgpu: MAPPING_ERROR: 0x0
[ 456.824378] amdgpu 0000:04:00.0: amdgpu: RW: 0x0
Output of amd.-info is as follows:
Thu May 6 16:23:31 CEST 2021
=== GPU 0, 04:00.0 Radeon RX 6800 XT 16368 MB ===
Bios: xxx-xxx-xxx
Core: 1240 MHz 875mV, Mem: 96 MHz
PerfCtrl: manual, Load: 99%, MemLoad: 0%, Power: 18.0 W, Cap: 272 W
Core: 31°C, HotSpot: 33°C, Mem: 32°C, Fan: 20%, RPM: 678
Core state: 1, clocks: 500 1240*
Mem state: 0, clocks: 96* 456 673 1064
SOC state: 0, clocks: 480* 1200
DCEF state: 0, clocks: 417* 1200
F state: 1, clocks: 500 666* 1941
PCIE Link speed:n/a, PCIE Link width:n/a
Memory total: 16368.00 MB, used: 4430.32 MB, free: 11937.68 MB, type: Samsung GDDR6
Can somebody tell me where the problem may be?
The same card works well under PhoenixMiner under Linux in an other computer.
Best regards, Avaron